Stability test chamber
The ZF model Stability Test Chamber (or Temperature and Humidity Chamber) is an ideal device for conducting stability tests in compliance with the ICH Q1A(R2) guideline. Featuring simultaneous control of temperature and humidity, this chamber ensures precise and reliable testing conditions. Its advanced data logging and control system, fully compliant with international standards such as GMP and GLP, sets it apart from similar devices worldwide.
The FG Stability Test Chamber is used in a wide range of laboratories, including: Industrial Pharmaceutical Investigation It is applicable.
Introduction of the New Generation of FG Stability Test Chambers
The most accurate chamber in the world with unique isotherm in accordance with the most reliable international standards
Quick return of the temperature to the set temperature after opening the device door
Uniformity @ 27 points of the chamber
High heating speed
Temperature stability
dual chamber
Double safety to protect your samples against unwanted increase or decrease in temperature
Adjustable safety thermostat with sensors (with two PT100 sensors)
According to the latest standards (TWW) DIN 12880 Class 3.3
The pleasure of using the most accurate cooling system in the world
The pleasure of using the most accurate cooling system in the world
Unparalleled cooling power even at high ambient temperature
No thrush
2 evaporator
The most resistant humidifier without deposits on the sensors
Prevention of Chemical Reactions and Corrosion of Water Level Sensors
To prevent water scaling on electronic sensors
Using electronic sensors to control the water level
Unique humidifier system
Inlet and outlet water source with separate pump (no need for inlet water and sewage piping)
Rapid return of humidity to the set value after opening the door
With extra water pump
The ability to precise adjust the humidity
Creating moisture at high speed
Accurate humidity sensor
Using the latest and most accurate ARM series microcontrollers
Controller lock system to prevent accidental changes
Graphical LCD display with touch buttons
Easy humidity calibration by the user in 2 humidity points
Easy temperature calibration by the user in 6 temperatures
PID controller to control temperature and humidity
Controller with 3 programs of 100 steps
Smart STM Temperature Check
Intelligent alarm of deviation from the set temperature and humidity
Discharge or Decrease of Water alarm
Device door open alarm
Sending SMS during alarms
Register DOCUMENTATION values
FGLAB software
Product video
To get to know More details of the product Watch the opposite video.
ZF technical specifications table
Customized equipment and services
IQ, OQ, PQ Certificates
Stainless steel tray
Alarm output relay
Network switch
Wi-Fi switch
Modem
Frequently Asked Questions(FAQ)
Considering that the water source of stability chambers is separate from the device, it is possible to disconnect the source from the device when entering the laboratory and reconnect it after installing the device, in which case the depth of the device without the source will be equal to 75 cm.
According to FG standards and the world’s valid standards, the best distance from the walls, floor and ceiling of the stability test chamber is 10% of the length of the same side, for example, if the width of the device is 40 cm, 10% is 4 cm from each side (left and right). ) and if the depth of the machine is 50 cm, 10% of that means 5 cm from the front and back, the distance from the walls of the machine should be considered for loading.
It always takes time for the internal chamber temperature to reach the set point. The Smart timer is activated when the temperature reaches the set point.
Since many centers do not have facilities such as water or sewage pipes, a feature has been placed in the FG stability chambers so that they can be installed and work properly independently of the deficiencies of the environment. Therefore, the FG stability test chamber is equipped with an inlet water source. And it is an exit and does not need plumbing.
Alarms should be such as to attract the user’s attention. Now imagine a device that repeatedly and unnecessarily alarms, such as when the door of the device is opened (naturally, the temperature of the device goes higher or lower). In normal devices, the alarm is activated, but in the FJ device, the alarm is activated only when it is needed and in The malfunctioning device is activated.
No, by using HCT technology, instead of water vapor entering the chamber, moist air enters the device, which prevents the samples from getting wet.
Yes, it can be done if needed by the consumers and according to the request.
Relative humidity has a direct relationship with heat, so there are always restrictions on devices that control both temperatures and humidity. FG devices are no exception, so it is recommended to chart the humidity temperature in the database of the devices FG is referred to.
If you still haven’t found the answer to your question, ask us.
"*" indicates required fields
